SKIL TS6307 vs DeWalt DWE7485 Jobsite Table Saw: Which Is Better? (October 2026)

On this page (15 sections)

1. SKIL table saw vs DeWalt table saw: blade and cut size
2. Stand and setup
3. Fence, guards and safety features
4. Power and dust collection
5. Which saw suits a garage shop?
6. Dado and groove cuts on each saw
7. Blade choice for an 8-1/4 inch saw
8. Working on a bench or stand
9. Setup checks for the first hour
10. Dust and cleanup on each saw
11. Sheet goods on each saw
12. Who should buy the SKIL TS6307
13. Who should buy the DeWalt DWE7485
14. How we scored the two saws
15. SKIL or DeWalt: the short answer

The SKIL TS6307 and the DeWalt DWE7485 are two portable table saws from the entry end of the jobsite range. Both have a 15 amp motor and a rack and pinion fence, and both suit a home workshop or garage.

The main difference is the blade and the stand. The SKIL has a 10-inch blade and a folding stand, and the DeWalt has an 8-1/4 inch blade and a compact footprint.

SKIL table saw vs DeWalt table saw: blade and cut size

The SKIL's 10-inch blade cuts deeper than the DeWalt's 8-1/4 inch blade. The two rip capacities are close, so the blade is the bigger difference.

The SKIL has a 25-1/2 inch rip capacity, and the DeWalt has 24.5 inches. That one-inch gap won't decide most jobs, since both saws rip the same lumber and trim.

For thicker stock, the 10-inch blade is the better fit. A larger blade gives a deeper cut, so the SKIL suits a shop that cuts thicker boards.

SKIL table saw and DeWalt table saw: blade and rip

Both saws rip to a fence, and both fences sit on rack and pinion rails. The difference shows up when the board is thicker than the smaller blade can cut through in one pass.

Check the depth numbers against your thickest lumber before you buy. The 10-inch blade gives you more margin, and the 8-1/4 inch blade asks you to plan around it.

Stand and setup

The SKIL folds its legs into a stand, while the DeWalt has no folding stand built in. That makes the SKIL ready to move and store, and the DeWalt ready to sit on a bench or a separate stand.

The SKIL's legs fold in to form the stand, which SKIL built in for portability and storage. It weighs about 51 pounds, so plan the lift and the path before you move it.

The DeWalt has a metal roll cage base, which DeWalt says is built for jobsite durability. It weighs about 54 pounds, a little more than the SKIL, and it doesn't come with a folding stand.

DeWalt also sells a stand version, the DWE7485WS, if you want a stand included. Check that any stand suits the saw's footprint before you order.

Fence, guards and safety features

Both saws use a rack and pinion fence, and both need their guard set up before the first cut. The guard systems differ in how they're built.

The SKIL's fence rails are rack and pinion, and its parallel blade alignment lets you adjust the blade against the rip fence and the miter slot. SKIL also builds in a safety anti-restart switch, which keeps the saw from restarting on its own after a power outage.

The DeWalt has rack and pinion telescoping fence rails and Site-Pro modular guarding. DeWalt includes a non-through cut riving knife and anti-kickback pawls, which you should set up as the manual directs.

SKIL includes a riving knife, an anti-kickback pawl and a blade guard. A riving knife and anti-kickback parts are features, not promises, and the manual sets the rules for both saws.

Power and dust collection

Both saws run a 15 amp motor, and the SKIL has a dust port elbow for cleanup. For the DeWalt, check the manual for its dust port size and the adapters that fit.

Connect a shop vac or a dust collector to the SKIL's elbow for cleanup. Table saw dust collection covers the ports and hoses that fit a portable saw.

Plug either saw into a circuit that can carry its 15 amp rating, and don't share that circuit with other heavy tools.

Which saw suits a garage shop?

The SKIL suits a garage that needs a saw it can fold and store. The DeWalt suits a small space where the saw stays put.

If the saw moves between a garage and a driveway, the SKIL's folding stand helps most. If the saw lives in one corner, the DeWalt's smaller footprint is easier to fit.

Dado and groove cuts on each saw

SKIL says a dado insert needs an 8-inch dado set. Check the arbor length and the throat plate before you buy a set, since a poor fit causes more trouble than a slow cut.

For the DeWalt, check the manual for dado support before you buy a set. Table saw dado blade explains what to look for in a set and what to confirm first.

Blade choice for an 8-1/4 inch saw

The DeWalt uses an 8-1/4 inch blade, and fewer blade options come in that size than in 10 inches. Check the options and the tooth count before you buy the saw, not after.

The SKIL uses a 10-inch blade, so its blade range is wider. The best table saw blades roundup lists the 10-inch choices for home shops.

Working on a bench or stand

The DeWalt needs a bench or stand, while the SKIL carries its own folding stand, so the setup differs in time and space. A bench for the DeWalt should be flat, stable and strong enough for the saw and the board.

Measure the bench height so the table sits at a comfortable working height for you. Check the saw is level before you cut, whichever stand you use.

Setup checks for the first hour

Before the first cut, check the blade alignment, the fence, the guard and the riving knife on either saw. Those four checks come before any cut.

Set the blade height, then check the blade is parallel to the fence and the miter slot. Both steps follow the manual's method.

Confirm the SKIL's anti-restart switch works as its manual describes. On the DeWalt, confirm the modular guarding is set and the riving knife is in place.

Dust and cleanup on each saw

The SKIL has a dust port elbow. For the DeWalt, plan cleanup with a shop vac set near the saw and an adapter that fits its port.

Keep the floor around either saw clear of offcuts, so you can move around the saw without stepping into the work area.

Sheet goods on each saw

Both saws can rip sheet goods, but a full sheet is heavy and needs support on both ends whichever one you choose. The narrow difference in rip width matters less than the support you set up around the saw.

For support ideas, read table saw outfeed table. It shows when a board needs support past the blade.

Who should buy the SKIL TS6307

Buy the SKIL if you want a 10-inch blade and a stand that folds away. It suits a garage or driveway shop that cuts lumber, trim and sheet goods on a regular schedule.

The 3-year limited warranty from SKIL is one more reason to consider it. Keep the receipt and the model number, TS6307-00, in case you need a claim.

Who should buy the DeWalt DWE7485

Buy the DeWalt if you want a compact saw for a small shop and a 24.5 inch rip capacity fits your sheets. It suits a small garage where the saw sits on a bench or a stand you already own.

It also suits people who want modular guarding that adjusts without tools, and a compact body that takes less room than the SKIL.

How we scored the two saws

Our score weighs specs, features and buyer feedback against what you're shopping for. On that basis, the SKIL scores 8.4 and the DeWalt scores 8.1.

The SKIL's score reflects its 10-inch blade, its folding stand and its 3-year warranty. The DeWalt's score reflects its compact footprint and guarding, with a smaller blade and no built-in stand pulling it down.

The SKIL is the 10-inch saw with the folding stand, and the DeWalt is the compact 8-1/4 inch saw. Each badge names the setup that suits that saw best.

SKIL or DeWalt: the short answer

The SKIL and the DeWalt are close on rip width, so the blade size and the stand decide the choice. Neither is the right saw for every shop.

Pick the SKIL TS6307 for a 10-inch blade and a folding stand. Pick the DeWalt DWE7485 for a compact footprint on a bench or stand you already own.

For a full look at each saw, read the SKIL TS6307 review or the DeWalt DWE7485 review. If a bigger saw is on your list, DeWalt DWE7491RS vs Bosch GTS15-10 covers the 10-inch end of the range.

Frequently asked questions

Which is better, the SKIL TS6307 or the DeWalt DWE7485?

Neither wins every case, since the SKIL has a 10-inch blade and a folding stand, while the DeWalt is more compact with a smaller blade. Match the saw to how you'll move it and where it sits.

Does the DeWalt DWE7485 rip 4x8 sheets?

DeWalt says its 24.5 inch rip capacity handles 4x8 sheet goods. A full sheet is heavy, so plan support on both ends before you start, and check the manual for the cut method it allows.

Does the SKIL TS6307 have a folding stand?

Yes, the legs fold in to form the stand, which SKIL built in for portability and storage. At about 51 pounds, plan the lift before you move it.