SKIL TS6307-00 10-Inch Jobsite Table Saw Review: Worth It? (October 2026)
The SKIL TS6307-00 is a 10-inch, 15 amp jobsite table saw with a folding stand built into its legs. It suits a garage or driveway shop that needs one saw it can fold, move and store, and it's a sensible pick for rips and crosscuts within its capacity.
On this page (15 sections)
- The SKIL TS6307-00 at a glance
- Is the SKIL TS6307 a good table saw?
- How the folding stand works
- Fence, blade alignment and cut capacity
- Safety setup and features
- Dust, power and cleanup
- Setup in the first hour
- Blade and blade changes
- Who it suits by type of work
- Keeping the saw accurate
- Pros and cons in plain words
- Who should buy the SKIL TS6307
- Alternatives to compare first
- How the TS6307 compares with the DWE7491RS
- Verdict on the SKIL TS6307-00
The SKIL TS6307-00 is a 10-inch jobsite table saw with a 15 amp motor and a folding stand built into its legs. This review covers the setup, the fence and cut capacity, the safety features and where the saw falls short.
If you're asking whether it's any good, start with the summary and the sections below. Then compare it with the other saws in this group before you decide.
The SKIL TS6307-00 at a glance
SKIL TS6307-00 10-Inch Jobsite Table Saw
- 10-inch blade, 15 amp motor
- 25-1/2 inch rip capacity
- Rack and pinion fence rails
- Integrated folding stand
- 0 to 45 degree bevel with stops at 0 and 45
- Dust port elbow
A 10-inch, 15 amp jobsite saw with a folding stand built into its legs, for a garage or driveway shop that needs to fold and store its saw.
Pros
- Folding stand built into the legs
- 25-1/2 inch rip capacity
- Rack and pinion fence rails
- 3-year limited warranty from SKIL
- Dust port elbow for cleanup
Cons
- About 51 pounds, so plan the lift and the path
- 25-1/2 inch rip capacity, shorter than the DeWalt DWE7491RS's
- SKIL says a dado set needs an 8-inch dado blade
It's a portable 10-inch saw with a 25-1/2 inch rip capacity and a cutting capacity of 4x4 stock at 90 degrees. The stand is made from the saw's own legs, which fold in for storage.
Buy it if you need one saw that folds up for storage, and you'll cut lumber and sheet goods within its rip capacity. Skip it if you need a rip wider than 25-1/2 inches or a saw for daily production work.
Is the SKIL TS6307 a good table saw?
For a portable saw with a folding stand, it's a sensible pick, as long as the cuts you make fit its 25-1/2 inch rip and its 4x4 cutting capacity. Whether it's good for you depends on your work.
SKIL's feature set covers the basics. It has rack and pinion fence rails, parallel blade alignment, a bevel from 0 to 45 degrees and a dust port elbow.
The bevel locks at two positive stops, 0 and 45 degrees, so the common angles are quick to reach. For garage projects with lumber and sheet goods, the saw covers the basics.
For daily production work or a rip wider than 25-1/2 inches, look at a larger saw.
How the folding stand works
The integrated legs fold in to form the stand, which keeps the saw compact for storage and transport. SKIL built the stand into the saw, so there's no separate stand to find or store.
Once folded, the saw takes less room in a garage corner and is easier to store against a wall. That's the main reason to choose this model over a bare saw.
At about 51 pounds, plan the lift and the path before you move it. Make sure the stand is stable before you cut, as the manual directs.
Fence, blade alignment and cut capacity
The rack and pinion fence and the parallel blade alignment matter most for accurate rips on this saw. Both are the features to check before the first cut.
The fence rails are rack and pinion, which lets you move the fence smoothly and set it precisely. SKIL's blade alignment lets you micro-adjust the blade parallel to the rip fence and the miter slot, so check that alignment against the manual's method before you start.
The rip capacity is 25-1/2 inches. SKIL says the saw cuts material up to 4x4 at 90 degrees, which covers common dimensional lumber.
SKIL includes a 10-inch 24-tooth carbide blade. For dadoes, SKIL says a dado insert needs an 8-inch dado set, so read table saw dado blade before you buy one.
Safety setup and features
The box includes a blade guard, a riving knife, an anti-kickback pawl and a push stick, plus the saw has a safety anti-restart switch. You still need to set up each part as the manual directs before the first cut.
SKIL says the anti-restart switch helps after a power outage, so the saw won't restart on its own when power returns. That's a useful feature, but it doesn't change how you should handle the blade.
A riving knife and an anti-kickback pawl reduce some risks, but they don't remove them. A table saw can kick a board back when the wood binds, which is why table saw kickback is worth reading before your first cut.
Wear eye and ear protection, use push sticks for narrow pieces and keep your hands clear of the blade's path. Those habits matter more than any single feature on the saw.
Dust, power and cleanup
The dust port elbow sends chips to a container, and the 15 amp motor needs a circuit that can carry it. Both points affect how the saw works day to day.
Connect a shop vac or dust collector to the elbow for cleanup. Table saw dust collection covers the ports and hoses that fit a portable saw.
Plug the saw into a circuit that can carry its 15 amp rating, and don't share that circuit with other heavy tools. Keep the cord clear of the cut line and the stand's legs, so nobody trips on it.
Setup in the first hour
Set the stand, the blade, the fence and the guard before the first cut. Each one takes a few minutes, and each one matters on the first board.
Check that the stand is stable on the floor and the legs are locked in position. A wobbly saw makes every cut harder to control.
Check the blade is parallel to the fence and the miter slot, using the manual's method. Then set the guard and the push stick in place before the saw runs.
Blade and blade changes
The saw comes equipped with a 10-inch 24-tooth carbide blade. More teeth give a finer cut, and fewer teeth clear wood faster.
SKIL TS6307 blade and cut capacity
The blade and its height set the depth of cut, and the 25-1/2 inch rip sets the widest board. Check both against the work you plan to do.
Unplug the saw before you change a blade. How to change a table saw blade explains the general routine, and the manual sets the steps for this saw.
Who it suits by type of work
It suits shelving, trim, small furniture and sheet goods cut within its capacity. Those jobs fit a 25-1/2 inch rip and a 10-inch blade.
It's not built for daily production or for rips wider than 25-1/2 inches. A bigger saw suits those jobs better.
If your shop is tight on space, the folding stand is the feature that matters most to you.
Keeping the saw accurate
A fence that picks up dust binds on the rails, so clean the rails and the table before a long session. Moving the saw can shift the alignment, so recheck it after each move.
Keep the guard and the anti-restart switch in working order, and replace a dull or damaged blade before you use the saw again.
Pros and cons in plain words
The folding stand is the reason to buy this saw. A 25-1/2 inch rip capacity covers most lumber and trim, and the rack and pinion fence makes setting it quick.
The downsides are weight and rip width. At about 51 pounds, it isn't a saw you'll carry far, and a rip wider than 25-1/2 inches needs a bigger saw.
Who should buy the SKIL TS6307
Buy it for a garage, driveway or basement shop that needs one saw with a stand that folds away. It suits someone who cuts lumber, trim and sheet goods on a regular schedule.
It's a poor fit for daily production work. If you need a compact option instead, the SKIL vs DeWalt comparison covers the smaller DeWalt, and best jobsite table saws shows the wider field.
Alternatives to compare first
Two other saws are worth a look before you buy. One is a compact saw for a small shop, and the other is a 10-inch saw on a lifting stand.
For a 10-inch saw with accessories in the box, the Evolution R10TS review is the one to compare.
How the TS6307 compares with the DWE7491RS
The TS6307 weighs about 51 pounds. The DeWalt DWE7491RS weighs about 110 pounds with its stand.
The SKIL's legs fold into the stand, so there's no separate stand to buy or store. The trade is rip width, with 25-1/2 inches on the SKIL against 32-1/2 inches on the DeWalt.
Pick the SKIL if you move the saw often. Pick the DeWalt if you rip wide boards.
Verdict on the SKIL TS6307-00
The SKIL TS6307-00 is a practical jobsite saw with a folding stand, and it scores 8.4 on our scale. Our score weighs specs, features and buyer feedback against what you're shopping for.
The SKIL earns its score from the folding stand, the 25-1/2 inch rip and the 3-year warranty. It loses some points for weight and a rip capacity shorter than the widest saws.
If the folding stand and the 10-inch blade match your work, it's a sensible buy. If they don't, compare the other saws in this group first.
Frequently asked questions
Is the SKIL TS6307-00 good for a beginner?
Any table saw can cause serious injury, so a beginner should start with the manual. The TS6307-00 includes a riving knife, an anti-kickback pawl, a blade guard and a push stick, and the manual shows how to set up each one.
What is the rip capacity of the SKIL TS6307?
The rip capacity is 25-1/2 inches, measured from the blade to the far side of the fence. That's the widest board you can rip in one pass, so check it against your widest board before you buy.
Does the SKIL TS6307-00 come with a warranty?
SKIL gives it a 3-year limited warranty. Keep the receipt and the model number, TS6307-00, and read what the warranty covers before you buy so you know what a claim needs.
Can the SKIL TS6307 cut a dado?
Only with a dado blade set that fits the saw. SKIL says a dado insert needs an 8-inch dado set, so check the manual and the arbor before you buy one, and read the dado blade guide first.
